Skip to content

Touch-Controlled RGB LED System ​

Project Overview ​

This project uses an Digicomp ESP32-S3 Dev Board to control an RGB LED using a built-in capacitive touch sensor.

Tapping the touch sensor cycles through 6 distinct color modes using PWM (Pulse Width Modulation):

  1. Red
  2. Green
  3. Blue
  4. Yellow
  5. White
  6. Off

Hardware Components ​

  • Digicomp ESP32-S3 Dev Board
  • Common Cathode RGB LED
  • Capacitive Touch Pad or Jumper Wire (Touch Pin)
  • Breadboard & Jumper Wires
  • USB-C Cable

Pin Connections ​

ComponentPin LabelESP32-S3 Pin
Touch Sensor / WireSignalGPIO 1
RGB LEDRed AnodeGPIO 4
RGB LEDGreen AnodeGPIO 5
RGB LEDBlue AnodeGPIO 6
RGB LEDCathodeGND

Connection Summary ​

  • Touch Pin → ESP32-S3 GPIO 1
  • RGB Red Pin → ESP32-S3 GPIO 4
  • RGB Green Pin → ESP32-S3 GPIO 5
  • RGB Blue Pin → ESP32-S3 GPIO 6
  • RGB Cathode Pin → ESP32-S3 GND

Software Setup ​

  • IDE: Arduino IDE
  • Board Package: ESP32 Board Manager by Espressif Systems
  • Board Selection: ESP32S3 Dev Module

Complete Arduino Code (main.ino) ​

cpp
// Define Pins
const int touchPin = 1; // GPIO 1 (TOUCH1)
const int redPin   = 4; // GPIO 4
const int greenPin = 5; // GPIO 5
const int bluePin  = 6; // GPIO 6

// Touch threshold: adjust if sensitivity is too high or low
const int TOUCH_THRESHOLD = 30000;

int currentMode = 0;
bool isTouched = false;

void setup() {
  Serial.begin(115200);

  pinMode(redPin, OUTPUT);
  pinMode(greenPin, OUTPUT);
  pinMode(bluePin, OUTPUT);

  // Set initial color (Off)
  updateColor();
}

void loop() {
  // Read touch value on ESP32-S3
  int touchVal = touchRead(touchPin);

  // Detect tap event (when value drops below threshold)
  if (touchVal < TOUCH_THRESHOLD && !isTouched) {
    isTouched = true;
    currentMode = (currentMode + 1) % 6; // Cycle through 6 modes (0 to 5)
    updateColor();
    delay(50); // Debounce delay
  }
  else if (touchVal >= TOUCH_THRESHOLD && isTouched) {
    isTouched = false; // Reset touch state when finger is removed
  }

  delay(20);
}

void updateColor() {
  switch (currentMode) {
    case 0: setColor(255, 0, 0);   break; // Red
    case 1: setColor(0, 255, 0);   break; // Green
    case 2: setColor(0, 0, 255);   break; // Blue
    case 3: setColor(255, 255, 0); break; // Yellow
    case 4: setColor(255, 255, 255); break; // White
    case 5: setColor(0, 0, 0);     break; // Off
  }
}

void setColor(int red, int green, int blue) {
  // For Common Cathode: PWM 0-255
  // (If using Common Anode, change to: 255 - red, etc.)
  analogWrite(redPin, red);
  analogWrite(greenPin, green);
  analogWrite(bluePin, blue);
}

Conclusion ​

This Touch-Controlled RGB LED System demonstrates capacitive sensing and PWM output control using the Digicomp ESP32-S3 Dev board. The state-machine logic prevents continuous cycling on long presses, delivering clean tap detection without requiring extra mechanical pushbuttons.

Contributors

The avatar of contributor named as Poojith Nirmal Poojith Nirmal

Changelog

Made in India